Warning/Indicator Lights and Warning Sounds
If a Warning Light Turns On or Flashes
Brake System Warning Indication/Warning Light
This warning has the following functions:
Warning light inspection
For an operation check, make sure that the light turns on when the ignition is switched on, and turns off a few seconds later or when the engine is started.
When the light turns on
If the brake system warning light remains illuminated the brake fluid may be low or there could be a problem with the brake system. Park the vehicle in a safe place immediately and contact an Authorized Mazda Dealer.
Refer to Inspecting Brake Fluid Level (Search).
Do not drive with the brake system warning light illuminated. Contact an Authorized Mazda Dealer to have the brakes inspected as soon as possible:
Driving with the brake system warning light illuminated is dangerous. It indicates that your brakes may not work at all or that they could completely fail at any time. If this light remains illuminated, after checking that the parking brake is fully released, have the brakes inspected immediately.
-
In addition, the effectiveness of the braking may diminish so you may need to depress the brake pedal more strongly than normal to stop the vehicle.
-
(With M Hybrid)
When starting the engine, the brake system warning light may turn on and the warning indication may be displayed. In this case, park the vehicle in a safe location and release the brake pedal.
If the brake system warning light/warning indication does not turn off even after parking the vehicle, have the vehicle inspected by an Authorized Mazda Dealer.
Charging System Warning Indication/Warning Light
If the warning light illuminates while driving, it indicates a malfunction of the alternator or of the charging system.
Drive to the side of the road and park off the right-of-way. Consult an Authorized Mazda Dealer.
Do not continue driving when the charging system warning light is illuminated because the engine could stop unexpectedly.
ABS Warning Indication/Warning Light
If the ABS warning light stays on while you're driving, the ABS control unit has detected a system malfunction. If this occurs, your brakes will function normally as if the vehicle had no ABS.
Should this happen, consult an Authorized Mazda Dealer as soon as possible.
-
When the engine is jump-started to charge the battery, uneven rpm occurs and the ABS warning light may illuminate. If this occurs, it is the result of the weak battery and does not indicate an ABS malfunction.
Recharge the battery.
-
The brake assist system does not operate while the ABS warning light is illuminated.
Master Warning Indication
The indication displays if the system has a malfunction.
Check the reason for the indication displaying on the center display or multi-information display.
Refer to If a Warning Light Turns On or Flashes (Search).
Brake Control System Warning Indication/Warning Light
The warning light illuminates when the system has a malfunction. Have your vehicle inspected at an Authorized Mazda Dealer.
Electric Parking Brake (EPB) Indication/Indicator Light
This warning has the following functions:
Parking brake warning/Indicator light inspection
The light illuminates when the parking brake is applied with the ignition switched to START or ON. It turns off when the parking brake is released.
When the light is flashing
The light flashes if the Electric Parking Brake (EPB) has a malfunction. If the light remains flashing even if the Electric Parking Brake (EPB) switch is operated, consult an Authorized Mazda Dealer as soon as possible.
Brake Override Warning Indication
This message is displayed when the accelerator pedal and brake pedal are depressed at the same time while driving.
Release the accelerator pedal and depress the brake pedal.
Check Engine Indication/Light
If this light illuminates while driving, the vehicle may have a problem. It is important to note the driving conditions when the light illuminated and consult an Authorized Mazda Dealer.
The check engine light may illuminate in the following cases:
-
The engine's electrical system has a problem.
-
The emission control system has a problem.
-
The fuel-filler cap is missing or not tightened securely.
-
The fuel tank level being very low or approaching empty.
If the check engine light remains on, or it flashes continuously , do not drive at high speeds and consult an Authorized Mazda Dealer as soon as possible.
If the check engine light turns on, do not disconnect the battery cables.
If the battery cables are disconnected and then reconnected, the engine could be damaged and catch on fire.
AWD Warning Indication/Warning Light (Some Models)
“AWD Malfunction. Front Wheel Drive Only. Have the Vehicle Inspected” is displayed/When the light is turned on
The indication is displayed/the light turns on under the following conditions. The system may have a malfunction. Have the vehicle checked at an Authorized Mazda Dealer.
-
When there is a malfunction in the AWD system.
“Excessive AWD System Load. Drive Slowly Until Warning Light Turns Off. Vehicle Now in Front Wheel Drive” is displayed/When the light is flashing
The indication is displayed/the light flashes under the following conditions. Park the vehicle in a safe place and check that the warning indication light turns off/ the warning light stops flashing, and then drive the vehicle. Contact an Authorized Mazda Dealer if the indication is continuously displayed.
-
When the differential oil temperature is excessively high.
-
When there is a large difference between the front and rear wheel rotation, such as when trying to remove the vehicle from mud.
“Mismatched Tire Diameters. Vehicle Now in Front Wheel Drive” is displayed/When the light is turned on
The indication is displayed/the light turns on under the following conditions. Inspect the tire sizes or tire pressures on all 4 wheels. Contact an Authorized Mazda Dealer if the indication remains on or the warning light remains illuminated.
-
When any of the tire diameter is different.
-
When any of the tire pressure is incorrect.
Security Indicator Light
If the security indicator light flashes continuously while you are driving, do not shut off the engine. Go to an Authorized Mazda Dealer and have it checked. If the engine is shut off while the indicator light is flashing, you will not be able to restart it.
Make sure the key is within the operational range for signal transmission. Switch the ignition off, and then restart the engine. If the engine does not start after 3 or more tries, contact an Authorized Mazda Dealer.
Because the electronic codes are reset when the immobilizer system is repaired, the keys are needed. Make sure to bring all the keys to an Authorized Mazda Dealer so that they can be programmed.
High Beam Control System (HBC) Warning Indication/Warning Light (Amber) (Some Models)
The light remains turned on if there is a problem with the system. Have your vehicle inspected at an Authorized Mazda Dealer.
Check Fuel Cap Warning Indication/Warning Light
Low Washer Fluid Level Warning Indication/Warning Light (Some Models)
This warning light indicates that little washer fluid remains.
Action to be taken
Add washer fluid (Search).
Tire Pressure Monitoring System (TPMS) Warning Indication/Warning Light (Turns on)
If a tire pressure decreases below the specified air pressure, the TPMS warning light turns on.
At the same time, a message and the tire pressure of each tire are displayed on the multi-information display alternately. In addition, the tire (s) with low air pressure is displayed in yellow.
Do not drive the vehicle at high speeds if the TPMS warning light turns on or flashes:
Driving the vehicle at high speeds while the TPMS warning light is turned on or flashing is dangerous because the brake performance and the steering wheel operability will be reduced. If the vehicle is driven at high speeds or the brakes are suddenly applied, it could lead to an accident. Gradually apply the brakes to lower the vehicle's speed.
Do not ignore the TPMS warning light when it is turned on or flashing:
Continuing to drive the vehicle while ignoring the illumination/flashing of the TPMS warning light is dangerous because a tire may burst which could lead to an accident. Take appropriate measures as soon as possible.
While the TPMS is learning the tire positions, such as immediately after a tire position has been changed, the tire pressure at the tire position prior to it being changed is displayed until the system completes the learning. For this reason, the tire pressures displayed for the tire positions may be different from the actual tire pressures at the tire positions.
Action to be taken
Adjust the tire pressures to the appropriate pressures.
Refer to Tire Inflation Pressure (Search).
-
Adjust the tire pressures while the tires are cool. Because the air pressure in the tires fluctuates depending on the temperature, before adjusting the tire pressures, let the vehicle sit for an hour or drive it only within a 1.6 km (1 mile) distance. If the tire pressures are adjusted while the tires are warm, the tire pressures may decrease below the specified air pressure after cooling down which could turn on the warning light. In addition, because the air pressure in the tires decreases when the ambient temperature is low, if the ambient temperature increases, an illuminated TPMS warning light may turn off. Under any circumstances, always adjust the tire pressures while the tires are cool.
-
After adjusting the tire pressures, the TPMS warning light turns off. If the TPMS warning light does not turn off, drive the vehicle at a speed of about 25 km (16 mph) or faster for 3 minutes or longer and make sure the warning light turns off.
If the TPMS warning light remains on even after adjusting the tire pressures, one of the tires may have a puncture.
KEY Indicator Light (Green) (Flashing)
“Low Key Fob Battery. Replace Battery” is displayed/When the light is flashing
When the key battery is low, the indication is displayed when the ignition is switched OFF.
Action to be taken
Replace the key battery.
Seat Belt Warning Beep
Front seat
Except Mexico
If the driver's seat belt is not fastened when the ignition is switched ON, a beep sound will be heard for about 6 seconds. If the driver or the front passenger's seat belt is not fastened and if the vehicle is driven at about 20 km/h (12 mph) or faster, or about 10 km/h (6 mph) or faster for a continuous 30 seconds, with the seat belt unfastened, a sound is activated continuously for a certain period.
Until a seat belt is fastened or a given period of time has elapsed, the beep sound will not stop even if the vehicle speed falls below 20 km/h (12 mph).
-
To allow the front passenger occupant classification sensor to function properly, do not place and sit on an additional seat cushion on the front passenger's seat. The sensor may not function properly because the additional seat cushion could cause sensor interference.
-
If a small child is seated on the front passenger's seat, the warning beep may not operate.
Mexico
If the vehicle speed exceeds about 20 km/h (12 mph) with the driver or front passenger's seat belt unfastened, a warning beep sounds continuously. If the seat belt remains unfastened, the beep sound stops once and then continues for about 90 seconds. The beep stops after the driver or front passenger's seat belt is fastened.
Until a seat belt is fastened or a given period of time has elapsed, the beep sound will not stop even if the vehicle speed falls below 20 km/h (12 mph).
-
Placing heavy items on the front passenger's seat may cause the front passenger's seat belt warning function to operate depending on the weight of the item.
-
To allow the front passenger seat weight sensor to function properly, do not place and sit on an additional seat cushion on the front passenger's seat. The sensor may not function properly because the additional seat cushion could cause sensor interference.
-
If a small child is seated on the front passenger's seat, the warning beep may not operate.
Rear seat
The warning beep only sounds if a seat belt is unfastened after being fastened.
Key Left-in-vehicle Warning Beep (With the advanced keyless function)
If all the doors and luggage compartment are locked using another key while the key is left in the cabin, the beep which sounds outside of the vehicle will be heard for about 10 seconds to notify the driver that the key is in the cabin. In this case, take out the key by opening the door. A key taken out of the vehicle using this method may not operate because its functions have been temporarily stopped. To restore the key's functions, perform the applicable procedure (Search).
Low Fuel Warning Beep
When the low fuel warning light flashes, a warning beep is activated once at the same time.
Brake System Warning Beep (With M Hybrid)
A warning beep is activated if a problem with the brake system occurs and the brakes may not work as intended. Decelerate the vehicle while checking the safety of the surrounding area, and park the vehicle in a safe place. After stopping the vehicle, contact an Authorized Mazda Dealer.
Brake Override Warning Beep
A warning beep is activated when the accelerator pedal and brake pedal are depressed at the same time while driving. Only depress the brake pedal.
Selector Lever Not In P or N Reminder Warning Beep (With M Hybrid)
A warning beep is activated continuously if the driver's door is opened with the selector lever in a position other than the P or N position when the engine is running. Shift the selector lever to the P or N position, or close the driver's door.
AUTOHOLD Warning Beep
Warning light flashes/message is displayed and beep sound is activated simultaneously for about 5 seconds when using AUTOHOLD function or when AUTOHOLD switch is operated.
Because a problem with AUTOHOLD function has occurred, AUTOHOLD function does not operate even if AUTOHOLD switch is operated.
If the warning light flashes/message is displayed and the beep sound is activated simultaneously, have your vehicle inspected at an Authorized Mazda Dealer.
Vehicle Problem Warning Beep
If any of the following problems occur, a warning beep is activated. Check the information regarding the warning indication in the instrument cluster or on the center display.
-
Automatic transmission problem
-
Increase in automatic transmission internal temperature
-
M Hybrid problem
-
Brake fluid amount decrease
-
Engine oil level sensor problem
-
Electric Parking Brake (EPB) problem
-
Engine hydraulic pressure decrease
-
Engine coolant temperature increase
-
Engine system problem
Blind Spot Monitoring (BSM) System Warning Beep (Some Models)
The Blind Spot Monitoring (BSM) warning beep operates when the turn signal lever is operated to the side where the Blind Spot Monitoring (BSM) warning light is illuminated.
Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) System Warnings (Some Models)
The Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) system warnings notify the driver of system malfunctions and cautions on use when required.
Check based on the beep sound.
|
Warning beep type |
Notification content |
|---|---|
|
The beep sounds 1 time while the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) is operating. |
If a malfunction occurs in the system, make sure that the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) has been canceled. |
|
The beep sounds intermittently while the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) is operating. |
The distance between your vehicle and the vehicle ahead is too close. Check the safety of the surrounding area and reduce vehicle speed. |
Collision warning (Some Models)
If there is a possibility of a collision with a vehicle ahead, a warning sound is activated at the same time as the warning indications are displayed in the instrument cluster or active driving display.
