Instrument Cluster

1. Tachometer

2. Multi-information Display

3. Engine Coolant Temperature Gauge

4. Fuel Gauge

5. Dashboard Illumination Switch

6. Speedometer

7. TRIP Switch

The speedometer indicates the speed of the vehicle.

The tachometer shows engine speed in thousands of revolutions per minute (rpm).

 

---

Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.

 

1. STRIPED ZONE^*1

2. RED ZONE^*1

1. The range varies depending on the type of gauge.

Close Caution

View Caution

 

---

When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.

Close Note

View Note

The screen content changes each time the INFO switch is pressed.

1. Basic display

2. Drive information display

3. i-ACTIVSENSE display

4. Message display^*1

1. Displayed only when a warning occurs.

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The driving distance for a specified interval is indicated. Two types (TRIP A, TRIP B) of interval distance can be measured.

The display changes each time the TRIP switch is pressed.

1. Odometer display

2. Trip meter A display

3. Trip meter B display

When returning the trip meter to “0”, press the TRIP switch for 2 seconds or longer while the trip meter is displayed.

 

---

If the lead-acid battery is disconnected for vehicle maintenance or other reasons, the trip meter display returns to “0”.

Close Note

View Note

Displays the engine coolant temperature. The blue range of the gauge indicates that the engine coolant temperature is low, and the red range of the gauge indicates that the engine coolant temperature is high and overheating.

 

---

If the engine coolant temperature gauge needle is in the red range, there is the possibility of overheating. Drive slowly to reduce engine load.

Refer to Taking Action with Overheating (Search).

Close Caution

View Caution

Brightening the dashboard illumination

Dimming the dashboard illumination

If you press the - switch again while the dashboard illumination is at maximum dimness, a sound is activated to notify you that the dimmer setting is at maximum dimness.

Function for canceling illumination dimmer

The illumination dimmer can be canceled by pressing the + switch while the instrument cluster is at maximum dimness and while the vehicle power is switched ON. If you press the + switch again while the illumination dimmer is canceled, a sound is activated to notify you that it is canceled. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

When the vehicle power is switched ON, the outside temperature is displayed.

 

---

The outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions.

Close Note

View Note

The maximum driving distance is calculated and displayed based on the current remaining fuel tank level and the fuel economy. When the maximum driving distance is 50 km (30 miles) or farther, the maximum driving distance indication decreases in 10 km (10 mile) increments, and when the maximum driving distance is shorter than 50 km (30 miles), it decreases in 1 km (1 mile) increments.

 

---

The maximum driving distance is just an approximate numerical value and differs from the actual driving distance. Drive the vehicle while checking the fuel gauge.

Close Note

View Note

This mode displays the average fuel economy by calculating the total traveled distance and the total fuel consumption since the vehicle was purchased or the past data was reset. The average fuel economy is calculated and displayed every 30 seconds.

This displays the current fuel economy by calculating the amount of fuel consumption and the distance traveled.

(e-SKYACTIV G)

(SKYACTIV-G)

 

---

• Displays the 0 position when the vehicle speed decreases to a constant speed or slower.

• The arrow on the scale indicates the average fuel economy.

Close Note

View Note

Displays the system status.

The direction the vehicle is moving is displayed in one of eight directions while the vehicle is being driven.

Displays a message to notify the user of the system operation status and malfunctions or abnormalities.

Follow the instructions indicated on the display.

Refer to How to Use the Multi-information Display (Search).