Instrument Cluster and Display

The speedometer indicates the speed of the vehicle.

The tachometer shows engine speed in thousands of revolutions per minute (rpm).

 

---

Do not run the engine with the tachometer needle in the RED ZONE.

This may cause severe engine damage.

 

Close Caution

View Caution

 

---

When the tachometer needle enters the STRIPED ZONE, this indicates to the driver that the gears should be shifted before entering the RED ZONE.

Close Note

View Note

The multi-information display indicates the following information.

• Odometer

• Trip meter

• Engine coolant temperature gauge

• Fuel gauge

• Outside temperature

• Distance-to-empty

• Average fuel economy

• Current fuel economy

• Maintenance Monitor

• Blind Spot Monitoring (BSM) Display

• Distance Recognition Support System (DRSS) Display

• Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) System Display

• Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Display

• Cruise Control Display

• Compass Display

• Warning message

The screen content changes each time the INFO switch is pressed.

The odometer is constantly displayed on the screen when the ignition is switched ON, and the TRIP A or TRIP B screen can be displayed by operating the INFO switch.

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The driving distance for a specified interval is indicated. Two types (TRIP A, TRIP B) of interval distance and the average fuel economy for each can be measured.

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the fuel tank is filled.

When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.

The trip meter and average fuel economy can be reset by pressing the INFO switch for 1.5 seconds or more while in each mode.

 

---

• Only the trip meters record tenths of kilometers (miles).

• The trip record will be erased when:

  • The power supply is interrupted (blown fuse or the battery is disconnected).

  • The vehicle is driven over 9999.9 km (mile).

Close Note

View Note

Displays the engine coolant temperature. The blue gauge indicates that the engine coolant temperature is low, and the red gauge indicates that the engine coolant temperature is high and overheating.

 

---

If the high engine coolant temperature warning light (red) flashes, there is a possibility of overheating. Drive slowly to reduce engine load until you can find a safe place to stop the vehicle and wait for the engine to cool down.

Refer to Overheating (Search).

Close Caution

View Caution

 

---

• If the engine coolant temperature is high or the engine is hot, the engine output may be limited.

• The temperature unit (Centigrade/Fahrenheit) of the engine coolant gauge display changes in conjunction with the temperature unit of the outside temperature display.

  Refer to Personalization Features (Search).

• During normal driving, the engine coolant temperature stabilizes at 100 °C (210 °F) or less, and the gauge indicates a range lower than 100 °C (210 °F).

Close Note

View Note

The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.

If the fuel level is low, () and () turn an amber color. Refuel as soon as possible.

Refer to Taking Action (Search).

 

---

• After refueling, it may require some time for the indicator to stabilize. In addition, the indicator may deviate while driving on a slope or curve since the fuel moves in the tank.

• The direction of the arrow () indicates that the fuel-filler lid is on the left side of the vehicle.

Close Note

View Note

(Without auto-light control)

When the lights are turned on with the ignition switched ON, the brightness of the dashboard illumination is dimmed.

(With auto-light control)

When the lights are turned on with the ignition switched ON, the brightness of the dashboard illumination is dimmed. However, when the light sensor detects that the surrounding area is bright such as when the lights are turned on in the daytime, the dashboard illumination does not dim.

 

---

• (With auto-light control)

  When the ignition is switched ON in the early evening or at dusk, the dashboard illumination is dimmed for several seconds until the light sensor detects the brightness of the surrounding area, however, the dimming may cancel after the brightness is detected.

• When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

  Refer to Headlights (Search).

Close Note

View Note

The brightness of the instrument cluster and dashboard illuminations can be adjusted by rotating the knob.

• The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.

• The brightness increases by rotating the knob to the right.

Function for canceling illumination dimmer

The illumination dimmer can be canceled by rotating the dashboard illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

 

---

• The illumination dimmer can be canceled by pressing the dashboard illumination knob.

• When the illumination dimmer is canceled, the instrument cluster cannot be dimmed even if the lights are turned on.

• When the illumination dimmer is canceled, the screen in the center display switches to constant display of the daytime screen.

Close Note

View Note

When the ignition is switched ON, the outside temperature is displayed.

 

---

• Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

  • Significantly cold or hot temperatures.

  • Sudden changes in outside temperature.

  • The vehicle is parked.

  • The vehicle is driven at low speeds.

Close Note

View Note

Changing the Temperature Unit of the Outside Temperature Display

The outside temperature unit can be switched between Celsius and Fahrenheit.

Settings can be changed by operating the center display screen.

Refer to Personalization Features (Search).

 

---

When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.

Close Note

View Note

This displays the approximate distance you can travel on the remaining fuel based on the fuel economy.

The distance-to-empty will be calculated and displayed every second.

 

---

• Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refueling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.

• The display will not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.

• The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge indicating the remaining fuel supply disappear.

• If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery cables are disconnected, the actual distance-to empty/range may differ from the amount indicated.

Close Note

View Note

The average fuel economy is calculated every minute from the total traveled distance on the trip meter and the total fuel consumption, and the average fuel economy for either TRIP A or TRIP B is displayed.

The average fuel economy and trip meters can be reset by pressing the INFO switch for 1.5 seconds or more while in each mode. After the data is cleared, the fuel consumption is recalculated and the - - - km/L (- - - mpg) for the 1 minute prior to it being displayed is indicated.

This displays the current fuel economy by calculating the amount of fuel consumption and the distance traveled.

 

---

Indicates the 0 position when the vehicle speed is about 5 km/h (3 mph) or slower.

Close Note

View Note

The following maintenance period notifications can be displayed by turning the Maintenance Monitor on.

• Scheduled Maintenance

• Tire Rotation

• Oil Change

When the remaining days to the maintenance period is 15 days or less, or the remaining distance is 1,000 km (600 miles) or shorter, a message is indicated when the ignition is switched ON.

For the setting method and indications for the maintenance monitor, refer to the Maintenance Monitor.

Refer to Maintenance Monitor (Search).

Displays the system status.

Refer to Blind Spot Monitoring (BSM) (Search).

Displays the system status.

Refer to Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) (Search).

Displays the currently set system status.

Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) (Search).

Displays the distance between your vehicle and the vehicle ahead.

Refer to Distance Recognition Support System (DRSS) (Search).

The vehicle speed preset using the cruise control is displayed.

Refer to Cruise Control (Search).

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Warning	Page
	Brake System Warning Indication/Warning Light*1*2	(Search)
	ABS Warning Light*1	Electronic Brake Force Distribution System Warning (Search)
		ABS warning (Search)
	Charging System Warning Indication/Warning Light*1	(Search)
	Engine Oil Warning Light*1	(Search)
(Red)	High Engine Coolant Temperature Warning Light*1	(Search)
	Power Steering Malfunction Indication	(Search)
	Master Warning Indication	(Search)
	Electric Parking Brake (EPB) Warning Indication/Warning Light*1	(Search)
	Check Engine Light*1	(Search)
	Automatic Transaxle Warning Indication	(Search)
	AWD Warning Indication (Some Models)	(Search)
	Air Bag/Front Seat Belt Pretensioner System Warning Light*1	(Search)
	Tire Pressure Monitoring System Warning Light*1 (Some Models)	Flashing (Search)
		Turns on (Search)
(Amber/White)	KEY Warning Indication	Amber (Search)
		White (Search)
(Amber)	High Beam Control System (HBC) Warning Indication/Warning Light*1 (Some Models)	(Search)
	Blind Spot Monitoring (BSM) Warning Indication (Some Models)	(Search)
(Amber)	Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) Warning Indication (Some Models)	(Search)
	Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) Warning Indication (Some Models)	(Search)
	LED Headlight Warning Light*1	(Search)
(Amber)	Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Indication (Some Models)	(Search)
	Low Fuel Warning Indication	(Search)
	Check Fuel Cap Warning Indication/Warning Light*1	(Search)
	Engine Oil Level Warning Light*1	(Search)
	Seat Belt Warning Light (Front seat)	(Search)
	Seat Belt Warning Light (Rear seat) (Some Models)	(Search)
	Low Washer Fluid Level Warning Indication (Some Models)	(Search)
	Door-Ajar Warning Indication	(Search)
	Liftgate-Ajar Warning Indication	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an Authorized Mazda Dealer.

2. The light turns on continuously when the parking brake is applied.

The wrench indication is displayed under the following conditions.

• When the preset maintenance period has arrived.

  Refer to Maintenance Monitor (Search).

• When the engine oil replacement period has arrived.

 

---

• The wrench indication may display earlier than the preset period depending on vehicle usage conditions.

• Whenever the engine oil is replaced, a reset of the vehicle engine control unit necessary.

  Your Authorized Mazda Dealer will be able to reset the engine control unit or see (Search) for the Vehicle engine control unit reset procedure.

Close Note

View Note

The speedometer indicates the speed of the vehicle.

The multi-information display indicates the following information.

• Odometer

• Trip meter

• Engine coolant temperature gauge

• Fuel gauge

• Outside temperature

• Trip Computer

• Cruise Control Display

• Compass Display

When the lights are turned on with the ignition switched ON, the brightness of the dashboard illumination is dimmed.

 

---

• When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.

  Refer to Headlights (Search).

Close Note

View Note

The brightness of the instrument cluster and dashboard illuminations can be adjusted by rotating the knob.

• The brightness decreases by rotating the knob to the left. A beep sound will be heard when the knob has been rotated to the maximum dim position.

• The brightness increases by rotating the knob to the right.

Function for canceling illumination dimmer

The illumination dimmer can be canceled by rotating the dashboard illumination knob to the right until a beep sound is heard while the instrument cluster is dimmed with the ignition switched ON. If the instrument cluster's visibility is reduced due to glare from surrounding brightness, cancel the illumination dimmer.

 

---

• When the illumination dimmer is canceled, the instrument cluster cannot be dimmed even if the lights are turned on.

• When the illumination dimmer is canceled, the screen in the center display switches to constant display of the daytime screen.

Close Note

View Note

When the ignition is switched ON, the outside temperature is displayed.

 

---

• Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

  • Significantly cold or hot temperatures.

  • Sudden changes in outside temperature.

  • The vehicle is parked.

  • The vehicle is driven at low speeds.

Close Note

View Note

Changing the Temperature Unit of the Outside Temperature Display

The outside temperature unit can be switched between Celsius and Fahrenheit.

Settings can be changed by operating the center display screen.

Refer to Personalization Features (Search).

 

---

When the temperature unit indicated in the outside temperature display is changed, the temperature unit indicated in the engine coolant gauge display changes in conjunction with it.

Close Note

View Note

The following information can be selected by pressing the INFO switch with the ignition switched ON.

• Distance-to-empty mode

• Average fuel economy mode

• Current fuel economy mode

• Compass mode

If you have any problems with your trip computer, consult an Authorized Mazda Dealer.

Distance-to-empty mode

This mode displays the approximate distance you can travel on the remaining fuel based on the fuel economy.

The distance-to-empty will be calculated and displayed every second.

 

---

• Even though the distance-to-empty display may indicate a sufficient amount of remaining driving distance before refueling is required, refuel as soon as possible if the fuel level is very low or the low fuel warning light illuminates.

• The display may not change unless you add more than approximately 9 L (2.3 US gal, 1.9 Imp gal) of fuel.

• The distance-to-empty is the approximate remaining distance the vehicle can be driven until all the graduation marks in the fuel gauge (indicating the remaining fuel supply) disappear.

• If there is no past fuel economy information such as after first purchasing your vehicle or the information is deleted when the battery cables are disconnected, the actual distance-to empty/range may differ from the amount indicated.

Close Note

View Note

Average fuel economy mode

This mode displays the average fuel economy by calculating the total traveled distance and the total fuel consumption since the vehicle was purchased or the past data was reset. The average fuel economy is calculated and displayed every minute.

To reset the displayed past data, press the INFO switch for 1.5 seconds or longer.

After resetting the data, - - - L/100 km (- - - mpg) is displayed for one minute before the fuel economy is recalculated and displayed.

 

---

If TRIP A is reset using the trip meter when the function which synchronizes (resets) the fuel economy monitor and the trip meter (TRIP A) is on, the displayed past data is reset.

Close Note

View Note

Current fuel economy mode

This mode displays the current fuel economy by calculating the amount of fuel consumption and the distance traveled.

Current fuel economy will be calculated and displayed every 2 seconds.

When you've slowed to about 5 km/h (3 mph), - - - L/100 km (- - - mpg) will be displayed.

Compass mode

The direction the vehicle is moving is displayed in one of eight directions while the vehicle is being driven.

The vehicle speed preset using the cruise control is displayed.

Refer to Cruise Control (Search).

These lights turn on or flash to notify the user of the system operation status or a system malfunction.

Signal	Indicator	Page
(Green)	KEY Indicator Light	(Search)
	Security Indicator Light*1	(Search)
	Wrench Indicator Light*1	(Search)
	Shift Position Indication	(Search)
	Lights-On Indication/Indicator Light	(Search)
	Headlight High-Beam Indicator Light	Headlight High-Low Beam (Search)
		Flashing the Headlights (Search)
	Turn Signal/Hazard Warning Indicator Lights	Turn and Lane-Change Signals (Search)
		Hazard Warning Flasher (Search)
(Green)	Brake Pedal Operation demand Indicator Light	(Search)
	TCS/DSC Indicator Light*1	Traction Control System (TCS) (Search)
		Dynamic Stability Control (DSC) (Search)
		Turns on (Search)
	TCS OFF Indicator Light*1	(Search)
	Select Mode Indication	(Search)
(White)	Cruise Main Indication	(Search)
(Green)	Cruise Set Indication	(Search)

1. The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started. If the light does not turn on or remains turned on, have the vehicle inspected at an Authorized Mazda Dealer.

When the ignition is switched ON, the wrench indicator light turns on and then turns off after a few seconds.

The wrench indicator light turns on under the following conditions:

• When the preset maintenance period has arrived.

• When it’s time to replace the engine oil.

Refer to Maintenance Monitor (Search).

 

---

• The wrench indicator light turns on earlier than the preset period depending on vehicle usage conditions.

• Whenever the engine oil is replaced, a reset of the vehicle engine control unit necessary.

  Your Authorized Mazda Dealer will be able to reset the engine control unit or see (Search) for the Vehicle engine control unit reset procedure.

Close Note

View Note