Switches and Controls

Lighting Control

Lighting Control

Flashing the Headlights

Can be used when the ignition is switched ON.

To flash the headlights, pull the lever fully towards you (the headlight switch does not need to be on).

 

The headlight high-beam indicator light in the instrument cluster illuminates simultaneously. The lever will return to the normal position when released.

 

Coming Home Light

The coming home light turns on the headlights (low beams) when the lever is operated.

To turn on the lights

When the lever is pulled with the ignition switched to ACC or OFF, the low beam headlights turn on.

The headlights turn off after a certain period of time has elapsed after the doors are closed.

 

  • The time until the headlights turn off after all of the doors are closed can be changed.

    Refer to Personalization Features (Search).

  • If no operations are done for 3 minutes after the lever is pulled, the headlights turn off.

  • The headlights turn off if the lever is pulled again while the headlights are illuminated.

Close Note
View Note
Rear Window Defogger

Mirror Defogger (Some Models)

The mirror defoggers defrost the outside mirrors.

 

The mirror defoggers operate in conjunction with the rear window defogger.

To turn on the mirror defoggers, switch the ignition ON and press the rear window defogger switch (Search).

HomeLink Wireless Control System (Type A) (Some Models)

Programming the HomeLink System

 

When programming a garage door opener or a gate, disconnect the power to these devices before performing programming. Continuous operation of the devices could damage the motor.

Close Caution
View Caution

The HomeLink system provides 3 buttons which can be individually selected and programmed using the transmitters for current, on-market devices as follows:

  1. Disconnect the power to the garage door opener or gate programmed to the hand-held transmitter.

  2. Position the end of your hand-held transmitter 2.5―7.5 cm (1―3 inches) away from the HomeLink button you wish to program while keeping the indicator light in view.

  3. Simultaneously press and hold both the chosen HomeLink and hand-held transmitter buttons. Do not release the buttons until step 3 has been completed.

     

    Some gate operators and garage door openers may require you to replace this Programming Step 2 with procedures noted in the “Gate Operator/Canadian Programming” section.

    Close Note
    View Note

  4. After the HomeLink indicator light changes from a slow to a rapidly blinking light, release both the HomeLink and hand-held transmitter buttons.

     

    If the HomeLink indicator light does not change to a rapidly blinking light, contact HomeLink at www.homelink.com or call 1-800-355-3515 for assistance.

    Close Note
    View Note

  5. Connect the power to the garage door opener or gate programmed to the hand-held transmitter.

  6. Firmly press and hold the programmed HomeLink button for five seconds, and then release it. Perform this operation two times to activate the door or gate. If the door or gate does not activate, press and hold the just-trained HomeLink button and observe the indicator light.

    If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released.

     

    To program the remaining two HomeLink buttons, begin with “Programming”― step 1

    Close Note
    View Note

    If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with “Programming” steps 7―9 to complete the programming of a rolling code equipped device (most commonly a garage door opener).

  7. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.

  8. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.)

     

    Complete the programming within 30 seconds.

    Close Note
    View Note

  9. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the “press/hold/release” sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming process.

HomeLink should now activate your rolling code equipped device.

 

To program the remaining two HomeLink buttons, begin with “Programming”― step 1

Close Note
View Note

For questions or comments, please contact HomeLink at www.homelink.com or 1-800-355-3515.

Page top