Switches and Controls
Lighting Control
Headlights
Turn the headlight switch to turn the headlights and other exterior lights on or off.
When the lights are turned on, the lights-on indicator light in the instrument cluster turns on.
-
If the light switch is left on, the lights will automatically switch off approximately 30 seconds after switching the ignition off.
The time setting can be changed.
Refer to Personalization Features (Search).
-
To prevent discharging the battery, do not leave the lights on while the engine is off unless safety requires them.
Without auto-light control
|
Switch Position |
 |
 |
 |
|||
|---|---|---|---|---|---|---|
|
Ignition Position |
ON |
ACC or OFF |
ON |
ACC or OFF |
ON |
ACC or OFF |
|
Headlights |
Off |
Off |
Off |
Off |
On |
On*2 |
|
Daytime running lights |
On*1 |
Off |
On*1 |
Off |
Off |
Off |
|
Taillights Parking lights License plate lights Side-marker lights |
Off |
Off |
On |
On*2 |
On |
On*2 |
-
The lights are turned on while the vehicle is driven.
-
The lights are turned on for the specified period by the auto headlight off function.
With auto-light control
|
Switch Position |
|
 |
|
|
||||
|---|---|---|---|---|---|---|---|---|
|
Ignition Position |
ON |
ACC or OFF |
ON |
ACC or OFF |
ON |
ACC or OFF |
ON |
ACC or OFF |
|
Headlights |
Off |
Off |
Auto*2 |
Auto*4 |
Off |
Off |
On |
On*5 |
|
Daytime running lights |
On*1 |
Off |
On*3 |
Off |
On*1 |
Off |
Off |
Off |
|
Taillights Parking lights License plate lights Side-marker lights |
Off |
Off |
Auto*2 |
Auto*4 |
On |
On*5 |
On |
On*5 |
-
The lights are turned on while the vehicle is driven.
-
The lights are turned on by the auto light function.
-
The lights are turned on while the vehicle is driven, and turned off when the headlights are turned on by the auto light function.
-
The lights are turned on continuously if the ignition is switched from ON to any other position with the lights turned on. The lights are turned on for the specified period by the auto headlight off function.
-
The lights are turned on for the specified period by the auto headlight off function.
Auto-light control (Some Models)
When the headlight switch is in the position and the ignition is switched ON, the light sensor senses the surrounding lightness or darkness and automatically turns the headlights and other exterior lights on or off.
-
Do not shade the light sensor by adhering a sticker or a label on the windshield. Otherwise the light sensor will not operate correctly.
-
The light sensor also works as a rain sensor for the auto-wiper control. Keep hands and scrapers clear of the windshield when the wiper lever is in the
position and the ignition is switched ON as fingers could be pinched or the wipers and wiper blades could be damaged when the wipers activate automatically. If you are going to clean the windshield, be sure the wipers are turned off completely when it is particularly tempting to leave the engine running. This is particularly important when clearing ice and snow.
-
The headlights and other exterior lights may not turn off immediately even if the surrounding area becomes well-lit because the light sensor determines that it is night time if the surrounding area is continuously dark for several minutes such as inside long tunnels, traffic jams inside tunnels, or in indoor parking lots.
In this case, the lights turn off if the light switch is turned to the
position. -
If the headlight switch and the windshield wiper switch are in
, and the wipers are operated at low or high speed by the auto wiper control for several seconds, bad weather conditions are determined and the headlights may be turned on. -
The sensitivity of the auto-light control may be changed.
Refer to Personalization Features (Search).
Headlight High-Low Beam
The headlights switch between high and low beams by moving the lever forward or backward.
When the headlight high-beams are on, the headlight high-beam indicator light is turned on.
Flashing the Headlights
Can be used when the ignition is switched ON.
To flash the headlights, pull the lever fully towards you (the headlight switch does not need to be on).
The headlight high-beam indicator light in the instrument cluster illuminates simultaneously. The lever will return to the normal position when released.
Coming Home Light
The coming home light turns on the headlights (low beams) when the lever is operated.
To turn on the lights
When the lever is pulled with the ignition switched to ACC or OFF, the low beam headlights turn on.
The headlights turn off after a certain period of time has elapsed after the doors are closed.
-
The time until the headlights turn off after all of the doors are closed can be changed.
Refer to Personalization Features (Search).
-
If no operations are done for 3 minutes after the lever is pulled, the headlights turn off.
-
The headlights turn off if the lever is pulled again while the headlights are illuminated.
Leaving Home Light
The leaving home light turns on the lights when the transmitter unlock button is pressed while away from the vehicle.
The following lights turn on when the leaving home light is operated.
Low beams, Parking lights, Taillights, License plate lights.
To turn on the lights
When the ignition switch and the headlight switch are in the following conditions, the headlights will illuminate when the transmitter unlock button is pressed and the vehicle receives the transmitter signal. The headlights turn off after a certain period of time has elapsed (30 seconds).
-
Ignition switch: off
-
Headlight switch:
, , or
-
Operation of the leaving home light can be turned on or off.
Refer to Personalization Features (Search).
-
When the transmitter lock button is pressed and the vehicle receives the transmitter signal, the headlights turn off.
-
When the headlight switch is turned to the
position, the headlights turn off.
Headlight Leveling
The number of passengers and weight of cargo in the luggage compartment change the angle of the headlights.
The angle of the headlights will be automatically adjusted when turning on the headlights.
Daytime Running Lights
Some countries require moving vehicles to have their lights on (daytime running lights) during the daytime.
The daytime running lights turn on when the vehicle is driven and turn off when the parking brake is operated or the selector lever is shifted to the P position.
(Except Canada)
The daytime running lights can be deactivated.
Refer to Personalization Features (Search).
Fog Lights (Some Models)
The fog lights can be turned on with the ignition switched ON and the headlights turned on.
Use this switch to turn on the fog lights. The fog lights will improve visibility at night and during foggy conditions.
The fog lights turn on when the fog light switch is turned to the 
position and turn off when the switch is turned to the position.
Turn and Lane-Change Signals
The ignition must be switched ON to use the turn and lane-change signals.
Turn Signals
Move the signal lever down (for a left turn) or up (for a right turn) to the stop position. The signal will self-cancel after the turn is completed.
If the indicator light continues to flash after a turn, manually return the lever to its original position.
The turn signal indicators in the instrument cluster flash according to the operation of the turn signal lever to show which signal is working.
-
If an indicator light stays on without flashing or if it flashes abnormally, one of the turn signal bulbs may be burned out.
-
A personalized function is available to change the turn indicator sound volume. (Search)
Lane-Change Signals
Move the lever halfway toward the direction of the lane change―until the indicator flashes― and hold it there. It will return to the off position when released.
Three-Flash Turn Signal
Windshield Wipers and Washer
The ignition must be switched ON to use the wipers.
Use only windshield washer fluid or plain water in the reservoir:
Using radiator antifreeze as washer fluid is dangerous. If sprayed on the windshield, it will dirty the windshield, affect your visibility, and could result in an accident.
Only use windshield washer fluid mixed with anti-freeze protection in freezing weather conditions:
Using windshield washer fluid without anti-freeze protection in freezing weather conditions is dangerous as it could freeze on the windshield and block your vision which could cause an accident. In addition, make sure the windshield is sufficiently warmed using the defroster before spraying the washer fluid.
If the windshield wipers are operated under cold weather conditions or during snowfall, they could stop due to accumulated snow on the windshield. If the windshield wipers stop due to accumulated snow on the windshield, park the vehicle in a safe place, turn the wiper switch off, and then remove the accumulated snow. If the wiper switch is turned to another position other than OFF, the wipers will operate. If the wipers do not operate even though the wiper switch is turned to a position other than OFF, consult an Authorized Mazda Dealer as soon as possible.
Windshield Wipers
Turn the wipers on by pressing the lever up or down.
With intermittent wiper
|
Switch Position |
Wiper operation |
|---|---|
 |
Operation while pulling up lever |
|
Stop |
 |
Intermittent |
 |
Low speed |
 |
High speed |
Variable-speed intermittent wipers
Set the lever to the intermittent position and choose the interval timing by rotating the ring.
With auto-wiper control
|
Switch Position |
Wiper operation |
|---|---|
|
Operation while pulling up lever |
|
Stop |
 |
Auto control |
|
Low speed |
|
High speed |
Auto-wiper control (Some Models)
When the wiper lever is in the position, the rain sensor senses the amount of rainfall on the windshield and turns the wipers on or off automatically (off―intermittent―low speed―high speed).
The sensitivity of the rain sensor can be adjusted by turning the switch on the wiper lever.
From the center position (normal), rotate the switch upward for higher sensitivity (faster response) or rotate it downward for less sensitivity (slower response).
-
Do not shade the rain sensor by adhering a sticker or a label on the windshield. Otherwise the rain sensor will not operate correctly.
-
When the wiper lever is in the
position and the ignition is switched ON, the wipers may move automatically in the following cases:-
If the windshield above the rain sensor is touched or wiped with a cloth.
-
If the windshield is struck with a hand or other object from either outside or inside the vehicle.
Keep hands and scrapers clear of the windshield when the wiper lever is in the
position and the ignition is switched ON as fingers could be pinched or the wipers and wiper blades damaged when the wipers activate automatically.If you are going to clean the windshield, be sure the wipers are turned off completely (when it is most likely that the engine is left running) this is particularly important when clearing ice and snow.
-
-
Switching the auto-wiper lever from the
to the position while driving activates the windshield wipers once, after which they operate according to the rainfall amount. -
The auto-wiper control may not operate when the rain sensor temperature is about －10 °C (14 °F) or lower, or about 85 °C (185 °F) or higher.
-
If the windshield is coated with water repellent, the rain sensor may not be able to sense the amount of rainfall correctly and the auto-wiper control may not operate properly.
-
If dirt or foreign matter (such as ice or matter containing salt water) adheres to the windshield above the rain sensor, or if the windshield is iced, it could cause the wipers to move automatically. However, if the wipers cannot remove this ice, dirt or foreign matter, the auto-wiper control will stop operation. In this case, set the wiper lever to the low speed position or high speed position for manual operation, or remove the ice, dirt or foreign matter by hand to restore the auto-wiper operation.
-
If the auto-wiper lever is left in the
position, the wipers could operate automatically from the effect of strong light sources, electromagnetic waves, or infrared light because the rain sensor uses an optical sensor. It is recommended that the auto-wiper lever be switched to the position other than when driving the vehicle under rainy conditions. -
If the headlight switch and the windshield wiper switch are in
, and the wipers are operated at low or high speed by the auto wiper control for several seconds, bad weather conditions are determined and the headlights may be turned on. -
The auto-wiper control functions can be turned off. Refer to Personalization Features (Search).
Windshield Washer
Pull the lever toward you and hold it to spray washer fluid.
If the windshield washer is turned on when the windshield wipers are not operating, the windshield wipers operate a few times.
If the washer does not work, inspect the fluid level (Search). If the fluid level is normal, consult an Authorized Mazda Dealer.
Rear Window Wiper and Washer
The ignition must be switched ON to use the wiper.
Rear Window Wiper
Turn the wiper on by turning the rear wiper/washer switch.
|
Switch Position |
Wiper operation |
|---|---|
|
Stop |
|
Intermittent |
 |
Normal |
Rear Window Washer
To spray washer fluid, turn the rear wiper/washer switch to either of the 
position. After the switch is released, the washer will stop.
If the washer does not work, inspect the fluid level (Search). If the fluid level is normal and the washer still does not work, consult an Authorized Mazda Dealer.
Rear Window Defogger
The rear window defogger clears fog from the rear window.
The ignition must be switched ON to use the defogger.
Press the switch to turn on the rear window defogger. The rear window defogger operates for about 15 minutes and then turns off automatically.
The indicator light illuminates when the defogger is operating.
To turn off the rear window defogger before the 15 minutes has elapsed, press the switch again.
-
Do not use sharp instruments or window cleaners with abrasives to clean the inside of the rear window surface. They may damage the defogger grid inside the window.
-
This defogger is not designed for melting snow. If there is an accumulation of snow on the rear window, remove it before using the defogger.
-
The rear window defogger setting can be changed. After changing the setting, the rear window defogger stops automatically after 15 minutes have elapsed and when the ambient temperature is high. When the ambient temperature is low, it continues to operate until the switch is pressed again.
Refer to Personalization Features (Search).
Mirror Defogger (Some Models)
The mirror defoggers defrost the outside mirrors.
The mirror defoggers operate in conjunction with the rear window defogger.
To turn on the mirror defoggers, switch the ignition ON and press the rear window defogger switch (Search).
Windshield Wiper De-icer (Some Models)
The thermal filaments at the following positions heat up and facilitate the removal of snow accumulated on the windshield.
The windshield wiper de-icer operates in conjunction with the rear window defogger.
To turn on the windshield wiper de-icer, switch the ignition ON and press the rear window defogger switch (Search).
Horn
To sound the horn, press the 
mark on the steering wheel.
Hazard Warning Flasher
The hazard warning lights should always be used when you stop on or near a roadway in an emergency.
The hazard warning lights warn other drivers that your vehicle is a traffic hazard and that they must take extreme caution when near it.
Depress the hazard warning flasher and all the turn signals will flash. The hazard warning indicator lights in the instrument cluster flash simultaneously.
-
The turn signals do not work when the hazard warning lights are on.
-
Check local regulations about the use of hazard warning lights while the vehicle is being towed to verify that it is not in violation of the law.
HomeLink Wireless Control System (Type A) (Some Models)
HomeLink and HomeLink house icon are registered trademarks of Gentex Corporation.
The HomeLink system replaces up to 3 hand-held transmitters with a single built-in component in the auto-dimming mirror. Pressing the HomeLink button on the auto-dimming mirror activates garage doors, gates and other devices surrounding your home.
Do not use the HomeLink system with any garage door opener that lacks the safety stop and reverse feature:
Using the HomeLink system with any garage door opener that lacks the safety stop and reverse feature as required by federal safety standards is dangerous. (This includes garage doors manufactured before April 1, 1982.)
Using these garage door openers can increase the risk of serious injury or death. For further information, contact HomeLink at 1-800-355-3515 or www.homelink.com or an Authorized Mazda Dealer.
Always check the areas surrounding garage doors and gates for people or obstructions before programming or during operation of the HomeLink system:
Programming or operating the HomeLink system without verifying the safety of areas surrounding garage doors and gates is dangerous and could result in an unexpected accident and serious injury if someone were to be hit.
Operating the HomeLink System
Press the programmed HomeLink button to operate a programmed device. The code will continue being transmitted for a maximum of 20 seconds.
Reprogramming the HomeLink system
To program a device to HomeLink using a HomeLink button previously trained, follow these steps:
-
Press and hold the desired HomeLink button. DO NOT release the button.
-
The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with “Programming” - step 1.
Pre-programming the HomeLink System
It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal.
-
Verify that there is a remote control transmitter available for the device you would like to program.
