Switches and Controls

Lighting Control

Flashing the Headlights

Can be used when the ignition is switched ON.

To flash the headlights, pull the lever fully towards you (the headlight switch does not need to be on).

 

The headlight high-beam indicator light in the instrument cluster illuminates simultaneously. The lever will return to the normal position when released.

 

Daytime Running Lights

Some countries require moving vehicles to have their lights on (daytime running lights) during the daytime.

 

The daytime running lights turn on when the vehicle is driven and turn off when the parking brake is operated or the selector lever is shifted to the P position.

 

(Except Canada)

The daytime running lights can be deactivated.

Refer to Personalization Features (Search).

Close Note
View Note
Turn and Lane-Change Signals

Turn Signals

Move the signal lever down (for a left turn) or up (for a right turn) to the stop position. The signal will self-cancel after the turn is completed.

 

If the indicator light continues to flash after a turn, manually return the lever to its original position.

The turn signal indicators in the instrument cluster flash according to the operation of the turn signal lever to show which signal is working.

 

 

  • If an indicator light stays on without flashing or if it flashes abnormally, one of the turn signal bulbs may be burned out.

  • A personalized function is available to change the turn indicator sound volume. (Search)

Close Note
View Note
Rear Window Wiper and Washer

Rear Window Wiper and Washer

The ignition must be switched ON to use the wiper.

HomeLink Wireless Control System (Type A) (Some Models)

Reprogramming the HomeLink system

To program a device to HomeLink using a HomeLink button previously trained, follow these steps:

  1. Press and hold the desired HomeLink button. DO NOT release the button.

  2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with “Programming” - step 1.

HomeLink Wireless Control System (Type B)

Programming the HomeLink System

The HomeLink system provides 3 buttons which can be individually selected and programmed using the transmitters for current, on-market devices as follows:

  1. Press and release the HomeLink button you would like to program. The indicator light flashes slowly in amber when the button is pressed.

  2. Hold the hand-held transmitter 2.5 to 7.5 cm (1 to 3 in) away from the HomeLink button you would like to program while keeping the indicator light in view.

     

    Depending on the hand-held transmitter, it may be easier to do the programming by holding it 15 to 20 cm (6 to 7.8 in) away from the HomeLink button.

    Close Note
    View Note

  3. Press the hand-held transmitter button continuously until the indicator light changes from amber (flashing) to green (on/flashing).

     

    Some gate operators and garage door openers may require you to replace this Programming Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section.

    Close Note
    View Note

  4. Press the HomeLink button again to check if the programming has been completed.

    • If the indicator light remains on in green, the programming is complete and the device becomes operational.

    • If the indicator light flashes rapidly in green, firmly press and hold the Homelink button and release it after two seconds have passed. Repeat this process up to three times to complete the programming. The device becomes operational and programming is complete. If the device does not operate, go to the next step.

  5. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.

  6. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.)

     

    Complete the programming within 30 seconds.

    Close Note
    View Note

  7. Return to the vehicle and firmly press and hold the Homelink button, and then release it after two seconds have passed. Repeat the “press/hold/release” sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming process.

    Press the programmed HomeLink button and make sure that the HomeLink System operates.

  8. If the status indicator arrows are flashing, refer to Garage Door Two-Way Communication.

 

To program the remaining two HomeLink buttons, go back to Step 1 of Programming the HomeLink System and repeat the procedure.

Close Note
View Note

For questions or comments, please contact HomeLink at www.homelink.com or www.youtube.com/HomeLinkGentex, or the HomeLink toll-free hotline at 1-800-355-3515 (for calls placed outside of the USA, Canada, and Puerto Rico, international rates will apply and may differ based on landline or mobile phone).

Erasing Programmed HomeLink Buttons

 

  • All of the programmed HomeLink buttons are reset. Individual buttons cannot be reset, however, individual buttons can be reprogrammed. For individual button reprogramming, refer to Reprogramming the HomeLink System (Search).

  • Verify that the programming has been erased if you resell the vehicle.

Close Note
View Note

  1. Press the two outer HomeLink buttons continuously at the same time until the indicator light flashes.

  2. Stop pressing the HomeLink buttons.

Page top