Instrument Cluster and Display

1. Power Meter
2. Multi-information Display
3. High Voltage Battery Power Gauge
4. High Voltage Battery Temperature Gauge
5. Dashboard Illumination Switch
6. Speedometer
7. TRIP Switch

The speedometer indicates the speed of the vehicle.

Indicates the discharge/charge status.

The higher the amount of charge while the EV system is regenerating power, the more the power meter needle is in the CHARGE zone. The higher the amount of discharge while discharging, such as the accelerator pedal is depressed, the more the power meter needle is in the POWER zone.

1. CHARGE zone

2. POWER zone

The CHARGE indicators indicate the electrical power which can be generated by regenerative braking, and the POWER indicators indicate the motor output status.

1. CHARGE indicators

2. POWER indicators

The CHARGE indicators turns off in stages when the power generated by regenerative braking cannot charge the high voltage battery. The POWER indicators turn off in stages when the motor output is restricted.

1. Multi-information Display

2. INFO switch

The multi-information display indicates the following information.

• Speedometer

• Odometer

• Trip meter

• Outside temperature

• Remaining high voltage battery power

• Distance-to-full discharge

• Average energy efficiency

• Instantaneous energy efficiency

• Charge status display

• i-ACTIVSENSE Display

• Compass Display

• Door-Ajar/Liftgate-Ajar Warning Indication^*1

• Message Display

1. Displayed when opening door/liftgate.

The screen content changes each time the INFO switch is pressed.

1. Basic display

2. Drive information display

3. i-ACTIVSENSE display

4. Charge status display^*1

5. Message display^*2

1. Displays only while charge connector is connected.

2. Displayed only when a warning occurs.

You can switch between the odometer and trip meter display using the TRIP switch.

1. TRIP switch

2. Odometer display

3. Trip meter A display

4. Trip meter B display

Odometer

The odometer records the total distance the vehicle has been driven.

Trip meter

The driving distance for a specified interval is indicated. Two types (TRIP A, TRIP B) of interval distance can be measured.

For instance, trip meter A can record the distance from the point of origin, and trip meter B can record the distance from where the high voltage battery was charged.

When trip meter A is selected, TRIP A will be displayed. When trip meter B is selected, TRIP B will be displayed.

The trip meter can be reset by pressing the TRIP switch for 1.5 seconds or more while the trip meter is displayed.

 

---

Only the trip meters record tenths of kilometers (miles).

Close Note

View Note

Displays the high voltage battery temperature. The blue range of the gauge indicates that the high voltage battery temperature is low and the red range indicates that it is high and overheating.

 

---

When the high voltage battery temperature is high or low, the output may be restricted to protect the EV system.

Close Note

View Note

When the power switch is switched ON, the outside temperature is displayed.

 

---

• Under the following conditions, the outside temperature display may differ from the actual outside temperature depending on the surroundings and vehicle conditions:

  • Significantly cold or hot temperatures.

  • Sudden changes in outside temperature.

  • The vehicle is parked.

  • The vehicle is driven at low speeds.

Close Note

View Note

Changing the Temperature Unit of the Outside Temperature Display

The outside temperature unit can be switched between Celsius and Fahrenheit.

Settings can be changed by operating the center display screen.

Refer to the Settings section in the Mazda Connect Owner's Manual.

The remaining amount of power in the high voltage battery is indicated by a percentage.

The direction the vehicle is moving is displayed in one of eight directions while the vehicle is being driven.

A message such as the system operation status, a malfunction, or an abnormality is indicated.

Warning/indicator light in instrument cluster turns on/flashes or symbol is indicated on display at same time as message

Check the information regarding the warning/indicator light or indicated symbol.

Refer to If a Warning Indication/Warning Lights (Search).

Refer to If a Indication/Indicator Lights (Search).

Message only is indicated on display

Follow the instructions indicated on the display. For the display content, refer to the next page.

Refer to If a Message Indicated on Multi-information Display (Search).

The wrench indication/indicator light is displayed/turns on under the following conditions.

• When the preset maintenance period has arrived.

  Refer to the Information section in the Mazda Connect Owner's Manual.

   

  ---

  • When the maintenance period arrives, have your vehicle inspected by an Authorized Mazda Dealer as soon as possible. If maintenance is neglected, a decrease in vehicle performance may occur which could cause damage. Have your vehicle inspected before the maintenance period arrives.

  Close Caution

  View Caution