Climate Control System

• If the vehicle has been parked in direct sunlight during hot weather, open the windows to let warm air escape, then run the climate control system.

• The climate control system measures inside and outside temperatures, humidity and sunlight using the sunlight/temperature sensor. It sets temperatures inside the cabin accordingly.

   

  ---

  Do not obstruct both sensors, otherwise the climate control system will not operate properly.

  Close Caution

  View Caution

  Sunlight sensor

  

  1. Sunlight sensor

  Interior temperature sensor

  

  1. Interior temperature sensor

• Clear all obstructions such as leaves, snow and ice from the hood and the air inlet in the cowl grille to improve the system efficiency.

   

  ---

  If the airflow of the climate control system significantly decreases, the air filter may be clogged. Replace the air filter.

  Close Note

  View Note

• Use the climate control system to defog the windows and dehumidify the air.

• Run the air conditioner about 10 minutes at least once a month to keep internal parts lubricated.

• Have the air conditioner checked before the weather gets hot. Lack of refrigerant may make the air conditioner less efficient.

  The refrigerant specifications are indicated on a label attached to the inside of the motor compartment. If the wrong type of refrigerant is used, it could result in a serious malfunction of the air conditioner. Consult a professional, government certified repairer for the inspection or repair because a special device is required for the air conditioner maintenance.

  For details, consult an Authorized Mazda Dealer.

1. Label

Operate the air conditioner (cooling, defrosting functions) with the EV system started. The air conditioner can be used while charging when the power switch is switched ON. In addition, Cabin preconditioning can also be used when the power switch is switched OFF.

 

---

When the charging is completed with the power switch switched ON, the air conditioner (cooling, heating, defrosting functions) stops automatically.

Close Note

View Note

1. Press the AUTO switch. Selection of the airflow mode, air intake selector and amount of airflow will be automatically controlled.

2. Operate the temperature setting switch/ (red) or (blue) to set the desired temperature.

    

   ---

   • The recommended set temperature is 25 °C (77 °F).

   • Setting the temperature to maximum hot or cold will not provide the desired temperature at a faster rate.

   • The power consumption of the air conditioner changes depending on the set temperature and the ambient temperature. If the set temperature is too low or high, the remaining distance to full discharge shortens.

   Close Note

   View Note

3. To turn off the system, press the climate control power switch.

Directing airflow

To adjust the direction of airflow, move the adjustment knob.

 

---

• When using the air conditioner under humid ambient temperature conditions, the system may blow fog from the vents. This is not a sign of trouble but a result of humid air being suddenly cooled.

• The air vents can be fully opened and closed by operating the knob.

Close Note

View Note

Side Vents

Air vent open/close

1. Knob

2. Open

3. Close

Airflow direction adjustment

1. Knob

Center Vents

Air vent open/close

1. Knob

2. Close

3. Open

Airflow direction adjustment

1. Knob

Dashboard Vents

Dashboard and Floor Vents

Floor Vents

Defroster and Floor Vents

Defroster Vents

 

---

The location airflow exits the air vents and the airflow amount may change depending on the open or close status of the air vents.

Close Note

View Note

 

---

Set the temperature control to the hot or warm position when defogging ( position):

Using the position with the temperature control set to the cold position is dangerous as it will cause the outside of the windshield to fog up. Your vision will be hampered, which could lead to a serious accident.

Close Warning

View Warning

Press the windshield defroster switch, or touch the .

In this position, the outside air position is automatically selected, and the air conditioner automatically turns on. The air conditioner will directly dehumidify the air to the front windshield and side windows. Airflow amount will be increased.

 

---

• If any of the following operations is done, the window glass will fog up more easily:

  • Switching to recirculate mode

  • Turning off the air conditioner (cooling, defrosting functions)

• For faster defrosting, do any of the following operations

  • Operate the fan control switch/ to increase the airflow amount

  • Operate the temperature setting switch/ (red) to increase the airflow temperature

• Only use the defroster when the window glass needs to be defogged. The power consumption of the air conditioner is suppressed, making driving more economical.

• For defrost mode, warm airflow is supplied for defrost even if the set temperature is decreased, however, this does not indicate a problem.

Close Note

View Note

Cabin preconditioning is a collective term regarding use of the Climate Control Timer and the remote climate control.

You can cool or warm the cabin, or defog the window glass before getting in the vehicle by setting your departure time in advance (Climate Control Timer) or by a remote operation (remote climate control) using your Smartphone.

 

---

Do not operate the cabin preconditioning with people or pets in the vehicle:

The cabin preconditioning may stop automatically due to the vehicle conditions and the surrounding environment. If the climate control system stops and the temperature inside the vehicle increases or decreases, it could cause a serious medical condition such as heat exhaustion and dehydration or even death.

Close Warning

View Warning

 

---

• If any of the following conditions are met, the cabin preconditioning will not operate. In addition, if the cabin preconditioning is operating, it will stop. However, if the liftgate is opened while the cabin preconditioning is operating, the cabin preconditioning will not stop.

  • The high voltage battery or the lead-acid battery charge is low

  • The doors/liftgate are open

  • The power switch is switched to a position other than OFF

  • There is a problem with the vehicle

• If the operation conditions are not met 30 minutes before the departure time set by the climate control timer, the climate control timer will not operate.

• If any of the following conditions is met, the climate control system will not operate effectively and the cabin temperature may not reach the set temperature:

  • Your power consumption is high

  • Extremely high or low temperatures

• The climate control system stops at the departure time. The cabin temperature may not reach the set temperature if you get in the vehicle earlier or later than the set departure time.

• If you operate the cabin preconditioning while charging the vehicle, it could take more time to charge the high voltage battery.

• During the cabin preconditioning operation, the cooling fan, the compressor, and the cabin fans operate, but this does not indicate a problem.

• The climate control system functions you can use differ depending on the power switch position.

  Function	Power switch position
  	OFF	ACC	ON (EV system off)	ON (EV system on)
  Air circulation	—	—	X	X
  Cooling/heating	—	—	X*1	X
  Climate Control Timer	X	—	—	—
  Remote climate control	X	—	—	—

  X: Available

  —: Not available

  1. The cooling/heating function can be used only while charging.

Close Caution

View Caution

 

---

• The recommended set temperature is 25 °C (77 °F). If you set an extremely high or low temperature, power consumption will increase and the charging time will take longer.

• If you operate the cabin preconditioning while the charging connector is connected, you can reduce the electric power consumption of the high voltage battery. Cabin preconditioning can be operated even without connecting the charging connector, however, the electrical power of the high voltage battery will decrease.

• If quick charge is started during cabin preconditioning, the cabin preconditioning is stopped.

• While the cabin preconditioning is operating, the indicator light for the climate control power switch turns on.

• The cabin preconditioning operates for 30 minutes. If you set the departure time using the Climate Control Timer, set it 30 minutes or later from the current time and if you want to make several settings, space them out at intervals of 30 minutes or longer.

• Enabling the defroster setting will aid you in defrosting and removing ice or snow from the window glass. The defroster performance changes according to the set temperature.

• The Climate Control Timer does not work immediately after the lead-acid battery is removed or installed, or when no GPS signal has been received. When GPS signals are received, the Climate Control Timer becomes operational.

Close Note

View Note

By setting the departure time using Mazda Connect, the climate control system operates and adjusts the cabin temperature by the departure time.

The departure time, day, set temperature, and defroster operation/non-operation can be personalized, and 7 types of patterns can be programmed in advance. You can check the cabin temperature and the setting status using your Smartphone while the Climate Control Timer is operating.

To operate the Climate Control Timer, switch the power switch OFF.

 

---

• The Climate Control Timer does not operate while the remote climate control is operating.

• The Climate Control Timer can be stopped by a Smartphone remote operation.

• When programming days for the Climate Control Timer, you do not have to set it every time because the programming continues into the following weeks.

Close Note

View Note

How to set the Climate Control Timer

 

---

Place a check in the check box for the function you want to enable () or uncheck it to disable () the function.

Close Note

View Note

1. Select “Settings” from the Mazda Connect home screen.

2. Select “EV Settings”.

3. Select “Climate Control Timer”.

4. Select the item setting you would like to change from the displayed content.

Climate Control Timer

Allows climate control to adjust cabin temperature before driving.

1. If an item selected using the cursor has been set, the item can be enabled or disabled.

2. Settings can be “Edit”/“Delete” by sliding an item selected using the cursor to the right.

Edit

The Climate Control Timer settings can be edited.

Using your Smartphone, you can turn on the climate control system remotely before departing. You can check the cabin temperature and the setting status using your Smartphone while the remote climate control is operating.

To operate the remote climate control, switch the power switch OFF.

Please refer to local Mazda website for more Connected Service information.

 

---

• To use the remote climate control, it is necessary to subscribe to Connected Service.

• The remote climate control can be used when your Smartphone is connected to your vehicle using the Connected Service.

• The remote climate control may not be available depending on the model of the Smartphone you are using. Please check in advance.

Close Caution

View Caution