Owner Maintenance

1. With the vehicle parked, pull the release handle to unlock the hood.

    

   

2. Insert your hand into the hood opening, slide the latch lever in the direction of the arrow as shown in the illustration, and lift up the hood.

    

   

    

3. Grasp the support rod in the padded area and secure it in the support rod hole indicated by the arrow to hold the hood open.

    

   

   1. Pad

   2. Support rod

1. Check under the hood area to make certain all filler caps are in place and all loose items (e.g. tools, oil containers, etc.) have been removed.

2. Lift the hood, grasp the padded area on the support rod, and secure the support rod in the clip. Verify that the support rod is secured in the clip before closing the hood.

    

   

   1. Clip

    

3. Lower the hood slowly to a height of about 20 cm (7.9 in) above its closed position and then let it drop.

 

---

When closing the hood, do not push it excessively such as by applying your weight. Otherwise, the hood could be deformed.

Close Caution

View Caution

 

---

If the brake fluid level is low, have the brakes inspected:

A low brake fluid level is dangerous.

A low level could indicate brake lining wear or a brake system leak which could cause the brakes to fail and lead to an accident.

Close Warning

View Warning

Inspect the fluid level in the reservoir regularly. It should be kept between the MAX and MIN lines.

The level normally drops with accumulated distance, a condition associated with wear of brake linings. If it is excessively low, have the brake system inspected by an Authorized Mazda Dealer.

 

---

• Hot waxes applied by automatic car washers have been known to affect the wiper's ability to clean windows.

• An operation malfunction may occur or the wiper effectiveness may be reduced if a water-repellent coating is used.

• To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.

• When the wiper lever is in the AUTO position and the power switch is switched ON, the wipers may move automatically in the following cases:

  • If the windshield above the rain sensor is touched.

  • If the windshield above the rain sensor is wiped with a cloth.

  • If the windshield is struck with a hand or other object.

  • If the rain sensor is struck with a hand or other object from inside the vehicle.

  Be careful not to pinch hands or fingers as it may cause injury, or damage the wipers. When washing or servicing the vehicle, make sure the wiper lever is in the OFF position.

• Before lifting the windshield wiper blades off the windshield, always follow the procedure for moving the windshield wiper blades. Otherwise, a wiper blade, wiper arm, or the hood could be damaged.

  Refer to the Replacing Windshield Wiper Blades (Search) section for the procedure on how to move the windshield wiper blades to the service position.

Close Caution

View Caution

Contamination of either the windshield or the blades with foreign matter can reduce wiper effectiveness. Common sources are insects, tree sap, and hot wax treatments used by some commercial car washes.

If the blades are not wiping properly, clean the window and blades with a good cleaner or mild detergent; then rinse thoroughly with clean water. Repeat if necessary.

If the buttons on the transmitter are inoperable and the operation indicator light does not flash, the battery may be dead.

Replace with a new battery before the transmitter becomes unusable.

 

---

• Make sure the battery is installed correctly. Battery leakage could occur if it is not installed correctly.

• When replacing the battery, be careful not to touch any of the internal circuitry and electrical terminals, bend the electrical terminals, or get dirt in the transmitter as the transmitter could be damaged.

• There is the danger of explosion if the battery is not correctly replaced.

• Dispose of used batteries according to the following instructions.

  • Insulate the plus and minus terminals of the battery using cellophane or equivalent tape.

  • Never disassemble.

  • Never throw the battery into fire or water.

  • Never deform or crush.

• Replace only with the same type battery (CR2032 or equivalent).

Close Caution

View Caution

The following conditions indicate that the battery power is low:

• A message, “Low Key Fob Battery. Replace Battery” is displayed on the multi-information display when the power switch is switched OFF.

• The system does not operate and the operation indicator light on the transmitter does not flash when the buttons are pressed.

• The system's operational range is reduced.

Incorrect battery replacement operation may damage the key. Replacing the battery at an Authorized Mazda Dealer is recommended. If replacing the battery by yourself, follow the instruction.

Replacing the key battery

1. Remove the lower cover while sliding the knob in the direction of the arrow.

   

2. Press in the tab to unlock the upper cover.

   

3. Insert a tape-wrapped flathead screwdriver into the gap and slide it in the direction of the arrow.

   

4. Twist the flathead screwdriver in the direction of the arrow and remove the upper cover.

   

5. Remove the cap using the tape-wrapped flathead screwdriver.

   

6. Remove the battery using tape-wrapped flathead screwdriver.

   

7. Insert a new battery into the transmitter so that the positive pole is facing up.

8. Install the cap.

   

9. Install the upper cover.

   

10. Insert the tabs of the lower cover into the slots of the transmitter and install the lower cover.

    

For reasons of proper performance, safety, and better energy efficiency, always maintain recommended tire inflation pressures and stay within the recommended load limits and weight distribution.

 

---

Using Different Tire Types:

Driving your vehicle with different types of tires is dangerous. It could cause poor handling and poor braking; leading to loss of control.

Except for the limited use of the temporary spare tire, use only the same type tires (radial, bias-belted, bias-type) on all four wheels.

Using Wrong-Sized Tires:

Using any other tire size than what is specified for the vehicle (Search) is dangerous. It could seriously affect ride, handling, ground clearance, tire clearance, and speedometer calibration. This could cause you to have an accident. Use only tires that are the correct size specified for the vehicle.

Close Warning

View Warning

All the light bulbs are the LED type.

The LED bulb cannot be replaced as a single unit because it is an integrated unit.

The LED bulb has to be replaced with the unit. If a replacement is necessary, consult an Authorized Mazda Dealer.

Your vehicle's electrical system is protected by fuses.

If any lights, accessories, or controls do not work, inspect the appropriate circuit protector. If a fuse has blown, the inside element will be melted.

If the same fuse blows again, avoid using that system and consult an Authorized Mazda Dealer as soon as possible.

Fuse block (Motor compartment)

Fuse block (Left side)