Switches and Controls

The coming home light turns on the headlights (low beams) when the lever is operated.

To turn on the lights

When the lever is pulled with the power switch switched to ACC or OFF, the low beam headlights turn on.

The headlights turn off after a certain period of time has elapsed after all of the doors are closed.

 

---

• The time until the headlights turn off after all of the doors are closed can be changed.

  Refer to the Settings section in the Mazda Connect Owner's Manual.

• If no operations are done for 3 minutes after the lever is pulled, the headlights turn off.

• The headlights turn off if the lever is pulled again while the headlights are illuminated.

Close Note

View Note

The leaving home light turns on the lights when the transmitter unlock button is pressed while away from the vehicle.

The following lights turn on when the leaving home light is operated.

Low beams, Parking lights, Taillights, License plate lights.

To turn on the lights

The headlights and the exterior lights turn on when the unlock switch on the key is pressed and the vehicle receives the key signal with the power switch and the headlight switch under the following conditions:

• Power switch: OFF

• Headlight switch: AUTO, , or

The headlights turn off after a certain period of time has elapsed (30 seconds).

1. Lock button

2. Unlock button

 

---

• Operation of the leaving home light can be turned on or off.

  Refer to the Settings section in the Mazda Connect Owner's Manual.

• When the transmitter lock button is pressed and the vehicle receives the transmitter signal, the headlights turn off.

• When the headlight switch is turned to the OFF position, the headlights turn off.

Close Note

View Note

The number of passengers and weight of cargo in the luggage compartment change the angle of the headlights.

Auto type

The angle of the headlights will be automatically adjusted when turning on the headlights.

A system malfunction or operation conditions are indicated by a warning.

Refer to Exterior Light Warning Indication/Warning Light (Search).

Manual type

When adjusting the illumination angle of the headlights, refer to the Settings section in the Mazda Connect Owner's Manual.

Select the proper headlight angle from the following chart.

×: Yes

―: No

The windshield wipers and washer can be used when the power switch is switched ON.

 

---

• When the wipers are not used during freezing temperatures or for a long time, the wiper rubber may adhere to the glass. If the wipers are operated while adhered to the glass, it could damage the wiper rubber and motor.

• If the wipers are operated while the glass is dry, the glass could be scratched and the wiper rubber damaged. When the glass is dry, spray washer fluid before operating the wipers.

• If the amount of washer fluid spray is insufficient, do not use the washer switch. If the washer switch continues to be operated with no washer fluid being sprayed, it could lead to pump damage.

Close Caution

View Caution

 

---

If the windshield wipers are operated under cold weather conditions or during snowfall, they could stop due to accumulated snow on the windshield. If the windshield wipers stop due to accumulated snow on the windshield, park the vehicle in a safe place, turn the wiper switch off, and then remove the accumulated snow. If the wiper switch is turned to another position other than OFF, the wipers will operate. If the wipers do not operate even though the wiper switch is turned to a position other than OFF, consult an Authorized Mazda Dealer as soon as possible.

Close Note

View Note

Turn the wipers on by pressing the lever up or down.

1. Indicator light

1. When the wiper lever is switched to the AUTO position, the indicator light turns on.

Auto-wiper control

When the wiper lever is in the AUTO position, the rain sensor senses the amount of rainfall on the windshield and turns the wipers on or off automatically (off―intermittent―low speed―high speed).

The sensitivity of the rain sensor can be adjusted by turning the switch on the wiper lever.

From the center position (normal), rotate the switch upward (+ direction) for higher sensitivity (faster response) or rotate it downward (- direction) for less sensitivity (slower response).

1. Switch

2. Higher sensitivity

3. Center position

4. Less sensitivity

 

---

• Do not shade the rain sensor by adhering a sticker or a label on the windshield. Otherwise the rain sensor will not operate correctly.

  

• Before lifting the windshield wiper blades off the windshield, always follow the procedure for moving the windshield wiper blades. Otherwise, a wiper blade, wiper arm, or the hood could be damaged.

  Refer to the Replacing Windshield Wiper Blades (Search) section for the procedure on how to move the windshield wiper blades to the service position.

• When the power switch is switched ON and the wiper lever is in the AUTO position, the windshield wipers may operate automatically in the following cases:

  • The area of the windshield above the rain sensor is touched or wiped with a cloth.

  • The windshield or the rain sensor area in the cabin is hit.

  When the power switch is switched ON and the wiper lever is in the AUTO position, do not touch the windshield or the windshield wipers Otherwise, the windshield wipers will operate automatically which could catch your fingers or damage the windshield wipers.

  When removing ice or snow, or cleaning the windshield, always make sure the wiper lever is in the OFF position.

Close Caution

View Caution

 

---

• Switching the auto-wiper lever from the OFF to the AUTO position while driving activates the windshield wipers once, after which they operate according to the rainfall amount.

• The auto-wiper control may not operate when the rain sensor temperature is about －10 °C (14 °F) or lower, or about 85 °C (185 °F) or higher.

• If the windshield is coated with water repellent, the rain sensor may not be able to sense the amount of rainfall correctly and the auto-wiper control may not operate properly.

• If dirt or foreign matter (such as ice or matter containing salt water) adheres to the windshield above the rain sensor, or if the windshield is iced, it could cause the wipers to move automatically. However, if the wipers cannot remove this ice, dirt or foreign matter, the auto-wiper control will stop operation. In this case, set the wiper lever to the low speed position or high speed position for manual operation, or remove the ice, dirt or foreign matter by hand to restore the auto-wiper operation.

• If the auto-wiper lever is left in the AUTO position, the wipers could operate automatically from the effect of strong light sources, electromagnetic waves, or infrared light because the rain sensor uses an optical sensor. It is recommended that the auto-wiper lever be switched to the OFF position other than when driving the vehicle under rainy conditions.

• If the headlight switch and the windshield wiper switch are in AUTO, and the wipers are operated at low or high speed by the auto wiper control for several seconds, bad weather conditions are determined and the headlights may be turned on.

• The auto-wiper control functions can be turned off.

  Refer to the Settings section in the Mazda Connect Owner's Manual.

Close Note

View Note

Pull the wiper lever toward you to spray washer fluid and operate the windshield wipers several times. The washer fluid is sprayed only while the windshield wipers move out of their stowed positions to the point where they start reversing back.

1. OFF

2. Washer

 

---

• If the windshield washer is turned on when the windshield wipers are not operating, the windshield wipers operate a few times.

• If you pull the wiper lever while the windshield wipers are reversing back to their stowed positions, the next time the washer fluid is sprayed is during the next cycle.

Close Note

View Note

If the washer does not work, inspect the fluid level (Search). If the fluid level is normal, consult an Authorized Mazda Dealer.

The rear window wiper and washer can be used when the power switch is switched ON.

To spray washer fluid, turn the rear wiper/washer switch to either of the position. After the switch is released, the washer will stop.

 

---

While the windshield washers are operating (from the time the wiper lever is pulled until the washer fluid stops spraying), the rear window washer does not spray washer fluid even if you operate the switch.

Close Note

View Note

If the washer does not work, inspect the fluid level (Search). If the fluid level is normal and the washer still does not work, consult an Authorized Mazda Dealer.

The rear window defogger clears fog from the rear window.

The rear window defogger can be used when the power switch is switched ON.

Press the switch to turn on the rear window defogger. The rear window defogger operates for about 15 minutes and then turns off automatically.

The indicator light illuminates when the defogger is operating.

To turn off the rear window defogger before the 15 minutes has elapsed, press the switch again.

1. Indicator light

 

---

• Do not use sharp instruments or window cleaners with abrasives to clean the inside of the rear window surface. They may damage the defogger grid inside the window.

Close Caution

View Caution

 

---

• This defogger is not designed for melting snow. If there is an accumulation of snow on the rear window, remove it before using the defogger.

• The rear window defogger operation time can be changed from 15 minutes to continuous operation. When the operation time has been switched to continuous operation, by pressing the switch, the rear window defogger will continue to operate until the power switch is switched OFF.

  Refer to the Settings section in the Mazda Connect Owner's Manual.

Close Note

View Note

The thermal filaments at the following positions heat up and facilitate the removal of snow accumulated on the windshield.

The windshield wiper de-icer operates in conjunction with the rear window defogger.

Press the rear window defogger switch when the power switch is switched ON to operate the windshield wiper de-icer (Search).

1. Indicator light

The mirror defoggers defrost the outside mirrors.

The mirror defoggers operate in conjunction with the rear window defogger.

Press the rear window defogger switch when the power switch is switched ON to operate the mirror defoggers (Search).

1. Indicator light

To sound the horn, press the mark on the steering wheel.

The hazard warning lights should always be used when you stop on or near a roadway in an emergency.

The hazard warning lights warn other drivers that your vehicle is a traffic hazard and that they must take extreme caution when near it.

Depress the hazard warning flasher and all the turn signals will flash. The hazard warning indicator lights in the instrument cluster flash simultaneously.

 

---

• The turn signals do not work when the hazard warning lights are on.

• Check local regulations about the use of hazard warning lights while the vehicle is being towed to verify that it is not in violation of the law.

Close Note

View Note

 

---

It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal.

Close Note

View Note

• Verify that there is a remote control transmitter available for the device you would like to program.

Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission ― which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.

If you live in Canada or are having difficulties programming a gate operator by using the programming procedures (regardless of where you live), replace Step 3 of Programming the HomeLink System with the following:

 

---

If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent possible overheating.

Close Note

View Note

While the indicator light is flashing in amber, press the button on the hand-held transmitter for 2 seconds and release it repeatedly until the indicator light changes from amber to green.

Go back to Step 4 of Programming the HomeLink System to complete the procedure.

Press the programmed HomeLink button to operate a programmed device.

The garage door two-way communication is a function that communicates with the garage door opener and indicates whether the garages door is open or closed using the indicator lights in the rear view mirror. It can indicate the status of the garage door within a range up-to 250 m (820 ft).

 

---

The communication range may shorten depending on obstructions.

Close Note

View Note

Programming two-way communication

Within five seconds after programming a new HomeLink button, both of the garage door status indicator lights will flash rapidly in green indicating that the garage door two-way communication has been established. If the garage door status indicator lights flash, the two-way communication programming is complete.

If the garage door status indicator lights do not flash, the two-way communication programming is not completed. For additional HomeLink information and programming videos, refer to the following Websites:

• www.HomeLink.com

• www.youtube.com/HomeLinkGentex

Operating the garage door two-way communication

By pressing HomeLink buttons 1 and 2 at the same time for two seconds, the status of the garage door is indicated for about 3 seconds as follows:

1. HomeLink button 2

2. HomeLink button 1

Garage door status	Indicator light
Closing	Amber flashes
Opening	Amber flashes
Closed	Green turns on
Opened	Green turns on

 

---

The programming will not be erased even if the battery is disconnected.

Close Note

View Note