Warning/Indicator Lights and Warning Sounds
High Voltage Battery Temperature Warning Indication
“Excessive High Voltage Battery Temperature. Drive Slowly” is displayed
The indication displays if the high voltage battery temperature is excessively high.
Drive slowly to reduce load on the high voltage battery.
Stop the vehicle in a safe place if necessary. If the indication remains displayed, the system may have a problem. Have the vehicle inspected by an Authorized Mazda Dealer.
“High Voltage Battery Temperature Is Low Acceleration Is Limited” is displayed
The indication displays if the high voltage battery temperature is excessively low.
The vehicle speed may not increase even if the accelerator pedal is depressed because the motor output is restricted.
If the indication remains displayed, the system may have a problem. Have the vehicle inspected by an Authorized Mazda Dealer.
Shift Control System Warning Indication/Warning light
The indication/light displays/turns on if the shift control system has a malfunction.
“Shift Control System Malfunction Stop the Vehicle in a Safe Location” displays/turns on
There is a serious malfunction with the shift control system.
Park the vehicle in a safe place immediately and contact an Authorized Mazda Dealer.
“Shift Control System Malfunction Have the Vehicle Inspected” displays/turns on
There is a malfunction with the shift control system.
Have your vehicle inspected by an Authorized Mazda Dealer.
“Vehicle Cannot Shift Into Park. Stop the Vehicle in a Safe Location Then Apply the Parking Brake” displays/turns on
The vehicle cannot be held in a stopped position even when the selector lever is in the P position.
When parking or stopping the vehicle, always apply the parking brake. In addition, the EV system may not start again if it is stopped.
Have your vehicle inspected by an Authorized Mazda Dealer.
ABS Warning Indication/Warning Light
If the ABS warning light stays on while you're driving, the ABS control unit has detected a system malfunction. If this occurs, your brakes will function normally as if the vehicle had no ABS.
Should this happen, consult an Authorized Mazda Dealer as soon as possible.
The brake assist system does not operate while the ABS warning light is illuminated.
Brake Override Warning Indication
This message is displayed when the accelerator pedal and brake pedal are depressed at the same time while driving.
Release the accelerator pedal and depress the brake pedal.
Security Indicator Light
If the security indicator light turns on/flashes while driving, do not stop the EV system (leave it operating) and have the vehicle inspected at an Authorized Mazda Dealer. If the EV system is stopped, it may not be restarted.
If the EV system cannot be started, switch the power switch OFF, place the key in another position within the operation range, and then restart the EV system.
Check the security indicator light and if it does not turn off, such as it remains on or flashes, switch the power switch OFF, wait for a while, and then restart the system.
If the EV system does not start after three attempts, a system malfunction may have occurred. Have the vehicle inspected by an Authorized Mazda Dealer.
Because the electronic codes are reset when the immobilizer system is repaired, the keys are needed. Make sure to bring all the keys to an Authorized Mazda Dealer so that they can be programmed.
Seat Belt Warning Indication/Warning Light (Front seat)
Seat Belt Warning Light (Rear seat) (Red)
If the rear seat belts are not fastened while the power switch is switched ON , the driver and the passenger are alerted by the warning light.
The warning light operates even if there is no passenger on the rear seat.
If a rear seat belt is not fastened by a certain period of time after the EV system has been started, the warning light turns off.
Action to be taken
Fasten the seat belts.
Door-Ajar/Liftgate-Ajar Warning Indication/Warning Light
The light turns on if any door/liftgate is not closed securely.
Action to be taken
Close the door/liftgate securely.
Key Removed from Vehicle Warning Beep
Vehicles with advanced keyless function
If the key is taken out of the vehicle while the power switch is switched to ACC or ON, and all the doors are closed, a sound is activated 6 times outside of the vehicle and a sound is activated 1 time in the vehicle.
Vehicles without advanced keyless function
If the key is taken out of the vehicle while the power switch is switched to ACC or ON, and all the doors are closed, a sound is activated 1 time in the vehicle.
Make sure that you leave the vehicle while carrying the key, or switch the power switch OFF.
Touch Sensor Inoperable Warning Beep (With the advanced keyless function)
A warning beep is activated to notify the driver that the doors are not locked when all of the following conditions are met:
-
The power switch is switched OFF.
-
All the doors and liftgate are not fully closed.
-
The lock is operated 3 times within 5 seconds.
Check the power switch and whether the doors and liftgate are open or closed, and then operate the lock again.
Key Left-in-luggage Compartment Warning Beep (With the advanced keyless function)
If the key is left in the luggage compartment with all the doors locked and the liftgate closed, a beep will be heard outside for about 10 seconds to notify the driver that the key is in the luggage compartment. In this case, take out the key by pressing the electric liftgate opener and opening the liftgate. The key taken out of the luggage compartment may not operate because its functions have been temporarily stopped. To restore the key's functions, perform the applicable procedure (Search).
Brake System Warning Beep
A warning beep is activated if a problem with the brake system occurs and the brakes may not work as intended. Decelerate the vehicle while checking the safety of the surrounding area, and park the vehicle in a safe place. After stopping the vehicle, contact an Authorized Mazda Dealer.
Selector Lever Not In P or N Reminder Warning Beep
A warning sound is activated if the following operations are performed while the selector lever is in a position other than P.
-
The power switch is switched OFF while the EV system is operating.
-
The driver’s seat belt is unfastened and the driver’s door is opened.
Check the selector lever position.
AUTOHOLD Warning Beep
Message is displayed and beep sound is activated simultaneously for about 5 seconds when using AUTOHOLD function or when AUTOHOLD switch is operated.
Because a problem with AUTOHOLD function has occurred, AUTOHOLD function does not operate even if AUTOHOLD switch is operated.
If the message is displayed and the beep sound is activated simultaneously, have your vehicle inspected at an Authorized Mazda Dealer.
Vehicle Problem Warning Beep
If any of the following problems occur, a warning beep is activated. Check the information regarding the warning indication in the instrument cluster or on the center display.
-
Brake system problem
-
Electric Parking Brake (EPB) problem
-
Shift control system problem
-
EV system problem
-
Charging system problem
-
Approaching vehicle audible system problem
Reverse Position Warning Beep
The warning beep is activated when the power switch is switched ON and the selector lever is in the R position.
Front Cross Traffic Alert (FCTA) Warning Beep (Some Models)
The Front Cross Traffic Alert (FCTA) warning beep is activated if there is a possibility of collision with a vehicle approaching from the front on the left and right sides of the vehicle.
Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) System Warnings (Some Models)
The Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) system warnings notify the driver of system malfunctions and cautions on use when required.
Check based on the beep sound.
|
Warning beep type |
Notification content |
|---|---|
|
The beep sounds 1 time while the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) is operating. |
If a malfunction occurs in the system, make sure that the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) has been canceled. |
|
The beep sounds intermittently while the Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go function) is operating. |
The distance between your vehicle and the vehicle ahead is too close. Check the safety of the surrounding area and reduce vehicle speed. |
Excessive Speed Warning (Some Models)
If the vehicle speed exceeds the speed limit sign displayed in the active driving display/instrument cluster, the area around the speed limit sign flashes in amber and the warning sound is activated at the same time. If the vehicle speed continues to exceed the displayed speed limit sign, the indication stops flashing and remains on.
Collision warning (Some Models)
If there is a possibility of a collision with a vehicle ahead, a warning sound is activated at the same time as the warning indications are displayed in the instrument cluster or active driving display.
Door-ajar Warning Beep
A warning beep is activated if the vehicle is driven with any door or liftgate ajar. Drive the vehicle after closing the doors and liftgate.
